[Piramides31]

Hello friend markus. thanks for answering. I will try to make a brief description of what I have done in my BMW E65 from 9/2002.

It originally comes with a navi01 analog TV browser. without logic 7. without CD loader. no dvd loader no voice module no rear entertainment. without assistant. the truth is very basic.
after getting hold of the inpa coding and programming programs. Ncs expert. dummy. ista d. etc and study a lot about how to use them, here is everything I have managed to do by myself at home and always with the help of great forums like this one and other bmw forums and also great colleagues. Thank you all.
This is what I have updated on my car.

1. idriver screen from 2006 working perfectly and coded with all the options that I wanted as a cd loader. dvd loader assistant. and tv that already had it from the factory.

2. ASK 2006 working perfectly and codified correctly, hence it can already have an auxiliary input.

3. 2006 idriver remote with the 4 buttons working perfectly.

4.2003 cd loader only read cd but great and working and encoded correctly.

5.IKHA from 2007 with the 4 buttons in full silver color and with everything correct and working perfectly, in this I had to put the front sensor and wire it to the rear central air outlet

6. 2007 light control with a silver button that works perfectly.

7.light module LM2. Year 2008 here it cost me a bit since I had to do more coding and programming but in the end it worked perfectly with welcome lights and all the options that I wanted.

8.Voice module year 2005 encoded and working perfectly.

9. Hybrid video module from the year 2007 working and coded correctly, hence the digital TV working with all the channels in Spain. I also have the TV in motion coded with ncs expert and dummy, hence I can see it in motion.

10.Navi 03. year 2006 working perfectly.

11. also change all the interior wood that was matte for a glossy one.


12.rear seat cup holder.

13. I keep the original phone module from 2002 with the sim card inserted. I also have the original phone from 2002 and it works great.

14 The last thing I have roofed is the dvd changer. I have read a lot about this I got one from 2004 that works great and I wanted to install it as described in the forum. that is to say, take the dvd pins pin 18 to pin 11 tv and pin 7 dvd to pin 3 tv and here my first problem in the blue plug of the video module the pins were at numbers 3 and 14 pin 11 was occupied with the current positive. then I go blank. Well then what I did is take the dvd cable pins 18 and 7 to pins 3 and 14 of the tv but there was no image only sound since the fiber optics of the dvd changer had connected it in line with the tv module . Ok remove the wires. So I had read that I could also make the connection to the browser pin 11 and pin 3 because there I took pins 18 and 7 of the dvd to navigation pins 3 and 11 now I had an image but with the problem that the image came out with stripes in both the tv as in the dvd. I'm blank again. good to say that the positive connect the dvd to the positive of the navigator and the negative to the post under the rear light. also say that everything I have updated I have coded correctly entering FA the new VO. in the case of the $696 and $698 DVD. Well, after reading a lot, I couldn't get the image to be seen without streaks and interference if I had the TV and DVD connected. So the last thing I did was disconnect the browser pins 3 and 11 and there I took the dvd pins 18 and 7 of the DVD. Now the dvd looks great but of course on the TV there is no image as the cables are loose. In short, I have not managed to have a correct image if I have the DVD and the TV connected. or is it one or the other. So my question is the following. the pins 11 and 3 of the navigator that I have loose and it is where the original tv signal entered where I have to put them??? What pin number should I connect them to??? in browser or in the tv module. I know there's something I'm missing. Or is it that you can't have TV and DVD running on the front screen at the same time. ???? I think there must be something I'm failing at. or is it that I'm missing codificar algo mas. ???? otra cosa es que en inpa en VIF. el cargador de dvd sale sin ninguna informacion todo en blanco y en ista D. el módulo me sale en rojo es decir no hay comunicación. se que ahi un problema. pero el DVD funciona muy bien no se si para que reconozca el mudulo en ista d tengo que desconectar el polo negativo de la batería 15 minutos o hacer un reinicio del most desde la guantera. ???? en el menu oculto de la pantalla idrive si tengo el dvd en el anillo most pero sin informacion. en fin perdonar que haya escrito tanto pero quería explicar todo la historia de actualización de mi coche. un fuerte abrazo amigo. decir que sigo buscando la solucion leyendo en todos los foros que conozco para resolver lo de la imagen y la TV y ver cómo hago que en ista D haya comunicación con el módulo de DVD. tengo que decir que me falta mucho por aprender pero me esfuerzo mucho para poder hacer todo yo mismo. Y también decir que con todos los programas de códing lo que uso es el cable k- dkan. A los módulos que llevan fibra óptica no le he hecho la programación del cambio de VIN por que he leído que para eso es mejor usar otros adaptador especial para la fibra óptica desde la guantera y yo lo lo tengo. Bueno agradesco cualquier consejo y ayuda. Recibe un cordial saludo